Summer Starts Here - Save up to 70%
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
These heavy-duty, aluminum crossbars work with Rhino-Rack legs to create a sturdy roof rack. The square bars include built-in C-channels for mounting Rhino-Rack heavy-duty, contractor-grade accessories.
Features:
Rhino-Rack HD Crossbars - Silver - Qty 2:Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
What's going on, everybody Adam here with etrailer. Today, we're gonna be taking a look at this really cool track system. It is the Rhino-Rack RT-Style roof rack track system. Some vehicles, we don't have the option to put a roof rack on the roof. Kind of like our Odyssey, we have here. Usually it's because of sliding doors, but there are some other instances, where we aren't gonna be able to put a roof rack on here.
But with these rails, it's going to allow us to do that. We can do a two-bar setup, to get a lot of accessories on our roof. With the Rhino-Rack kit, we have two different cross bars to pick from, and two different colors for each. Or we can just go with the arrow cross bars. It's gonna be a little bit quieter up on your roof, a little bit more aerodynamic.
And then, we're gonna have the HD bars as well. So pick whichever ones you think is gonna be best for you. In my opinion, the arrow bars are typically the ones that are gonna work with most of your accessories. On the one side, we're gonna have an open little slot, so we don't have to remove anything, to put in our accessories. And with our towers that we're using, for the arrow bar system, all of your accessories are gonna slide in this little end cap here.
So you don't have to remove anything, which is nice. And it goes all the way along the whole entire track. So you really find out exactly where you wanna put your bars. And it's gonna accept a block that is about 1 inch by 13/16 of an inch. The Rhino-Rack system is awesome, when it comes to taking your towers and your crossbars off.
All you need is your key. You're gonna unlock this, and look at that. All you gotta do is pull these in, pull this out, and we're gonna have a little end cap here. If you wanted to take these off, all you have to do is just take the little tool, loosen it, and slide it all the way off. But I do not mind having these on here, cause it's gonna be a lot quicker than your other option, which is Thule. The Thule ones, the towers are gonna take a little bit longer to take off, but they won't leave this little bottom section. So that's kind of all up to you. I like having these here, just because it makes for adjusting the whole entire roof rack a lot quicker. And also, I just don't mind the look. I think it kind of looks cool. So, if I we're to go with one of the two kits, you have an option for, whether it's a Thule or the Rhino-Rack, I would definitely go with the Rhino-Rack. So if we wanted to go back to the bare track system, it would just loosen it up, and then you can just go ahead and slide it out and we're done. So, I think that's also gonna be quicker, than the Thule option, which is why I really like the Rhino-Rack. Of your two options, both the Thule and the Rhino-Rack, the track system is gonna be a flat black. Which I think that's the best looking, in my opinion. I don't know if it's just because of our white car, but it does look really, really good. And that's pretty much it, for a look at the Rhino-Rack RT-Style roof rack track system..
Average Customer Rating: 4.6 out of 5 stars (14 Customer Reviews)
These heavy-duty, aluminum crossbars work with Rhino-Rack legs to create a sturdy roof rack. The square bars include built-in C-channels for mounting Rhino-Rack heavy-duty, contractor-grade accessories.
Product itself is fantastic, I strongly recommend.
I have had these on for more than a year. Most common use case is carrying a 60lb, 16' long canoe.
I installed with rivets into the roof sheet metal. No issues at all with any rivets coming loose, and zero leakage. I use it with a Yakima crossbars with the quick release mounts. The feet are bolted to the tracks. The crossbars just click into the feet. They take literally less than a minute to attach or remove. I've had a few roof rack systems and this is by far the best.
I used the etrailer videos for the installation and they were more than enough. The riveting was nerve-wracking on the first one, but actually very simple. I suggest really taking your time to assure parallel. This can be tricky depending on your roofline. I marked a centerline down my roof and set the tracks based on that.
The only downside I have run into is not at all a fault in the tracks. Because they rivet into the roof sheet metal, it's susceptible to a bit of flex. I see this under the front of the tracks when I crank down on the bowline of the boat. That's a very large lever pulling down on the rack into the roof sheet metal. No lasting issues, I can just see the metal move.
Another small thing to note is that if your roof is curved where the front or real of the rail lands, the plastic end cap might have a small gap under it. It's not itself held down to the roof, it just slots into the track. I have a small gap on mine and it's not a functional issue at all.
Wish they had a kayak rack to mount to areo bars
The rivets are way too small and they popped out from the roof top leaving holes on the roof of my van. Totally dissatisfied and angry.
Kit was great, except my SnugTop cover required longer T-Bolts for mounting the tracks. The 1.5 inch ones provided were too short. It was a little tough sourcing T/Bolts that would work. It would have been nice if longer T-Bolts could have been an option from Rhino Rack.
I don't use it as often as I would like but after a year it is still attached and works as intended. The rubber strips to reduce noise came partially loose, but with some fiddling they seem to be hanging in there now. For my vehicle at least, I used a professional (local auto shop) to install as I was not going to take a drill to my car.
Excellent customer service. First set of crossbars was delivered to the wrong address and a second set was mailed out to us arriving in a week.
They do vibrate a bit due to flat side facing into the wind. Could the leading edge be rounded to lessen this?
Fit perfectly and we're very happy with the roof rack.
The entire rack system (tracks, feet, aero crossbars, ladder straps, and load stops) installed and worked great for the intended use. Also, the service from etrailer was excellent.
The only drawback to this system is the necessity of purchasing a pneumatic rivet gun ($40) for mounting the tracks, but hey, it's a custom rack and i ended up with a cool tool.
Thanks.
Mostly satisfied. Not issue of etrailers and nothing really wrong with the product but do find it funny and a bit dumb that RhinoRack gives you security screws to hold feet to track but the rails are attached with a standard bolt that can be easily seen and accessed by anyone.
The directions were a bit challenging to follow but I figured it out . Racks are great an Ed our rep was great.
Nice rack system, strong and durable. Used on a Ford e350 to mount solar panels. Only draw back, one of the L brackets that goes under the rain gutter was not bent square enough and this caused the bracket to slide off when tightened. I had to adjust this with a clamp and hammer, no issues since.
I got the roof rack mounted anyways. Better pics to come when it's all finished!
I was building a rack for the skin on frame sailboat I built. I needed a crossbar on the top of my truck but the tracks were longer than I needed. I ended up cutting one of the tracks in half and redrilling the holes for the end caps on the cut ends. It was a little difficult to bend the track along the curved profile of my 2019 Ram Classic roof and get the holes where I needed. It says not to use a pop riveter but I didn't have a pneumatic one and have very good grip strength. I needed every bit of my grip strength in both hands to make it work but it did, in fact work. I used tape to cover the track around the rivets and prevent scratches because when the rivets pop, it's a little out of control. Overall it turned out well. I ended up machining a custom crossbar and T nuts due to having a machine shop on my garage.
I’ve had this rhino rack for over 3 years and it’s been excellent on long road trips to the ski slopes. A year after my purchase, I realized that I was missing the plastic coverings that attached to the end of the bars and called their customer service to resolve the missing pieces. I was impressed with their quick response and seamless delivery.
Do you have a question about this Roof Rack?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.